HL HL3511AD020 Silencers (HL3511AD020)

SILENCER FOR HEAVY DUTIES OEM NO:432 407 0700

Zhejiang Hengli Brake Valve Co., Ltd.

HL HL Pump Water

Pump water for iveco

Zhejiang Hengli Brake Valve Co., Ltd.

HL HL1608PT Clutch Servo for MAN (HL1608PT)

CLUTCH SERVOS FOR MAN OEM NO: 970 051 1320 DIA: 102MM

Zhejiang Hengli Brake Valve Co., Ltd.

Wanji XF Horizontal Fluidizing Dryer (XF)

Fluidizing dryer is also called fluid bed. Through operation and improvement over 30 years, it has play an active part in the fields of pharmaceutical, chemical, foodstuff, gain and so on industries. It consists of air filter, fluid bed, cyclone separator, dust collector, high-speed centrifugal fan, control cabinet and so on. Because of the difference of property from raw material, it is necessary to equip dust remover in accordance with practical needs. It may select cyclone separator and dust collector both or one of them. In general, cyclone separator can be selected if the raw material is larger and the dust collector may be selected if the raw material is light. Moreover, there is pneumatic feeding device for your selection. The clean and hot air enters into fluid bed through distributor of valve plate. The wet material is fed from the feeder forms the fluid state by hot air. Because of the wide contact between hot air and raw materials, the time of drying is short. The air enters from the front of bed, fluidized in bed for several minutes, and float another side of bed. The machine works in negative pressure. Drying process of medicines, chemical raw material, foodstuff, grain processing, feed and so on. For example, raw medicine, tablet, Chinese medicine, foodstuff of health protection, drinks, feed, resin, citric acid and other powders. The suitable diameter of raw material is normally 0.1-0.6mm. The most applicable diameter of raw material will be 0.5-3mm. Notes: the drying capacity is measured based on the primary moisture of crystal of plum is 20% and its final moisture is 5% and the temperature of air inlet is 130 degree . The drying capacity of other raw materials will be based on the practical drying condition. When choose models, please note that: Model A should be matched with cyclone separator and Model B with inside bag dust collector and Model C with cyclone separator and bag dust collector. Explanation to installation All equipment should be horizontal and fixed with foundation screw on the ground. All parts should be sealed well. The fan may be installed outdoor or in the special noise free room. The plan can be adjusted slightly in accordance with the real conditions. spec\itemdrying capacity kg/hpower of fanair pressure paair amount m 3 /hTem. of inlet air(degree)Max consume JForm of feedingXF1010-157.55.5×10 3150060-2002.0×10 81. shape valve 2. pneumatic conveyingXF2020-25115.8×10 3200060-2002.6×10 8XF3030-40157.1×10 3385060-2005.2×10 8XF5050-80308.5×10 3700060-2001.04×10 9

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji SZG SZG Series Double Cone Rotating Vacuum Dryer

Description SZG Series Conical Vacuum Dryer is a new generation drying device developed by our factory on the basis of combining the technology of similar equipment. It has two connecting ways, i. E. Belt or chain. Therefore it is stable in operation. The special design guarantees two shafts realize good concentricity. Heat medium and vacuum system all adapt reliable rotating connector with the technology from USA. On this basis, we also developed SZG-A. It can carry out steeples speed change and constant temperature control. As a specialized factory in drying industry, we supply hundred sets to the customers every year. As for working medium, it may be thermal oil or steam or hot water. For drying the adhesive raw material, we have designed specially a stirring plate buffer for you. Principle Let heat source (for example, low pressure steam or thermal oil) pass through the sealed jacket. The heat will be transmitted to raw material to be dried through inner shell; Under driving of power, the tank is rotated slowly and the raw material inside it is mixed continuously. The purpose of reinforced drying can be realized; The raw material is under vacuum. The drop of steam pressure makes the moisture (solvent) at the surface of raw material become saturation and will evaporate. The solvent will be discharged through vacuum pump and recovered in time. The inner moisture (solvent) of raw material will infiltrate, evaporate and discharge continuously. The three processes are carried out unceasingly and the purpose of drying can be realized within a short time. Application It is suitable for the raw materials that need to concentrate, mixed and dried at low temperature (for example, biochemistry) products in chemical, pharmaceutical and foodstuff industries. Particularly it is suitable for the raw materials that are easy to be oxidized, volatilized and have night heat sensitivity and is toxic and not permitted to destroy its crystal in drying process. Speed adjusting motor of 0-6rpm might be chosen according to the user's requirements. The following aspects should be point out when to order: 1. The above-mentioned parameters are calculated based on material density of 0.6g/cm3. If it's over, please point out. 2. If certificate for pressure vessel is required, please point out. 3. If glass lining for interior surface is required, please point out. If the material is explosive, or flammable, the calculation should be made according to trial result. Features When oil is used to heat, use automatic constant temperature control. It can be used for drying biology products and mine. Its temperature of operation can be adjusted form 20-160 degree. Compared to ordinal dryer, its heat efficiency will be 2 times higher. The heat is indirect. So the raw material can not be polluted. It is in conformity with the requirement of GMP. It is easy in washing and maintenance. itemspecnameunit100200350500750100015002000300040005000total volumeL100200350500750100015002000300040005000working volumeL501001752503755007501000150020002500heating aream 21.161.522.633.54.615.587.510.212.114.1speedrpm65444powerkw0.751.11.51.523345.57.57.5rotating heightmm18101910209021952500266529153055353038004180total weightkg8251050135016501800207022503000450053506000design pressure inside the tankmpa-0.09- -0.096design pressure of jacketmpa0.3

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji DW DW Series Mesh-Belt Dryer

Description This machine is a continuous penetrating flow drying equipment applied for drying pieces strip and particles state materials with good ventilation. The machine is suitable for the materials such as dewatering vegetable, herbal medicine of traditional Chinese medicine and others, for which the water contents are high and high drying temperature is not allowed. The machine owns the advantages, of fast drying speed, high evaporation capacity and good product quality. The de-watered & filtered cake state paste material should be made into particles or strips before drying process. Principle The materials are uniformly distributed on the mesh-belt by the material feeder. The mesh-belt generally adopts 12-60 mesh stainless steel mesh and it is drawn by a transmission device and move inside the dryer. The dryer is composed of several sections. For each section, the hot air is circulated separately. Part of exhausted gas is exhausted by a special moisture exhaust blower. The waste gas is controlled by an adjustment valve. The hot air passes through the mesh-belt covered with bring water material away. The mesh-belt moves slowly, running speed can be freely adjusted according to the material property. The final products after the drying process will fall into the material collector continuously. The top and low circulation units can be freely equipped according to the user's requirements. The number of section might be selected according to the production demands. Application De-watering vegetable, particle feed, gourmet powder, shredded coconut stuffing, various pigments and dyestuffs, compound rubber, acral fibre, medicine product, medicine material, small wooden product, plastic product, aging and solidification for the electronic component and device. specDW-1.2-8DW-1.2-10DW-1.6-8DW-1.6-10DW-2-8DW-2-10unit number4646 46belt Width m1.21.21.61.622drying section Length m810810810Thickness of the material mm10-80Temperature ()60-130steam Pressure Mpa0.2-0.8steam Consumption Kgsteam/KgH 2 O2.2-2.5drying strength KgH 2 O/h6-20kg/m 2 .htotal power of blower Kw3.34.46.68.81216total power of equipment KW4.055.157.359.5513.117.1 unitthree units series specialized machine for vegetablefive layers specialized machine for vegetable(Frame type)model DWP-2-10-3DWF-2-10-3DW5-3-12effective belt widthm223effective belt lengthm/unit101012tandemquantity 33 layers 5vegetable capacitykg/h6007202000evaporate strengthkg/h400-510480-6401440-1800consumption of steamKgsteam/KgH 2 O2.2-2.52.2-2.52.2-2.4heat radiation aream 290014402600total power of the machinekw7052150overall sizem33.2×2.58×2.833.2×2.27×2.8515.3×4.3×8.5heat source type steam, theermal conductivity oil, hot air furnace, electric Specialized machine for feed (frame type)modelunitDWZ-3×12effective belt widthm3effective belt lengthm/unit12using temperaturedegree80-130pressure of steamMpa0.4-0.8drying timemin35-50thickness of materialcm5-8drying strengthkg/h6-20consumption of steamKgsteam/KgH 2 O2-2.4total power of the machinekw76overall sizem15.1×4.3×3.4

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji HD HD Series Three Dimensional Mixer Machine

HD Series Three Dimensional mixer machine The barrel for charging the materials is driven by the driving shaft. The barrel body carries on the repeated level movement, rotation, turning and other complex movements so that the materials will carry out the three dimensions and complex movements along the barrel body so as to realize the various movements of the materials. Through disseminating, gathering, agglomerating and mixing to realize uniform mixing. The mixing barrel of the machine moves in multi-direction. For the materials, there is no centrifugal function, without the specific gravity segregation and the layer division. For each of build-up phenomenon, there is the remarkable weight rate. The mixing rate is high. The machine is the desired one of various mixers at present. The material charge rate of barrel is big. Maximum rate can be up to 90% (while normal mixer has only 40-50% of charge rate. ). It is high in efficiency and short in mixing time. The barrel adopts arc shape connections and its well polished. The machine is used for mixing the powder state and grain state materials to achieve high uniformity in the pharmaceutical, chemical, food, light-industry, electronic, mechanical, metallurgical, nation defense industries and other science and technology institutes. specSYH-5SYH-15SYH-50SYH-100SYH-200SYH-400SYH-600SYH-800SYH-1000SYH-1200SYH-1500SYH-2000volume of barrel(L)515501002004006008001000120015002000charge volume (L)4.513.54590180360540720900108013501800charge weight(kg)1.5-2.74-8.115-2730-5450-108100-216150-324200-432250-540300-648400-810500-1080rotation speed of main shaft(r/min)0-200-200-200-200-150-150-130-100-100-90-90-8motor power(Kw)0.250.371.11.52.245.57.511111518.5size LxWxH(mm)600×1000 ×1000800×1200 ×10001150×1400 ×13001250×1800 ×15501450×2000 ×15501650×2200 ×15501850×2500 ×17502100×2650 ×20002150×2800 ×21002000×3000 ×22602300×3200 ×25002500×3600 ×2800weight(kg)10020030080012001200150017001800200024003000

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji YZG/FZG Vacuum Dryer (YZG/FZG)

1. Under the condition of vacuum, the boiling point of raw material will decrease and that can make the pushing force become greater. Therefore for a certain amount of heat radiation, the conducting area of evaporator can be saved. 2. The heat source for operation of evaporation may be low pressure steam or surplus heat steam. 3. Before drying, the treatment of disinfection can be carried out. During the period of drying, there is no impurity material mixing, which is in conformity with the requirement of GMP. 4. It belongs to static drier. So the shape of raw material to be dried can not be destroyed. 5. It is certain that vacuum drying is to put raw material to the state of vacuum for heating and drying. If use vacuum pump to take air and humidity out, the dry speed will become much faster. 6. It is suitable for drying heat sensitive raw materials that can decompose and polymerize and metamorphose at high temperature. It is widely used in pharmaceutical, chemical, foodstuff and electronic industries. 7. Note: If use condensator, the solvent in raw material can be recovered. If use SK series water ring vacuum pump or ZSWJ series hydraulic inject vacuum pump sets, condensator can not be used and the investment could be saved. Model/name YZG-600 YZG-800 YZG-1000 YZG-1400 FZG- 15 Inside size of chamber(mm) 600*976 800*1274 1000*1527 1400*2054 1500*1400*1220 Size of chamber(mm) 1153*810*1020 1700*1040*1335 1693*1190*1500 2386*1657*1920 1513*1924*2060 Layers of baking shelf(mm) 4 4 6 8 8 Distance of baking shelf(mm) 81 82 102 102 122 Size of baking disk(mm) 310*600*45 460*600*45 460*640*45 460*640*45 460*640*45 Number of baking disk(mm) 4 8 12 32 32 Permitted pressure inside the pipe baking shelf(MPa) ≤0.784(8kgf/cm3) ≤ 0.784 ≤0.784 ≤0.784 ≤0.784 Temperature inside chamber ≤150 ≤150 ≤150 ≤150 ≤150 Vacuum inside chamber(MPa) ≤-0.095 When vacuum is 30 and the heating temperature is 1100C, vaporized rate of water 7.2 If use condensator, type and power of vacuum pump(kW) kw 2X-15A 2KW 2X-30A 3KW W3 5.5KW W3 7.5KW 2X-70A 7.5KW If not use condensator, type and power of vacuum pump (kw) SK-0.8 2.2KW SK-3 5.5KW SK-3 5.5KW SK-3 7.5KW SK-3 7.5KW Weight of drying ( kg ) 250 600 800 1000 2100 Chamber

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji HZG Rotating Cylinder Dryer (HZG Series)

Descriptions Wet material is loaded from one head of the dryer, and then it is stirred by the bafflers that is uniformly distributed in the barrel. Material is uniformly distributed and dispersed in the dryer, fully contact the hot air of parallel (or counter) flow, so the drying process is expedited, and the impulsion power of media transfer is enhanced. During the drying process, material is under the effect of angled baffler and hot air, moves to the star shape unloader that is at the other head of the dryer. Applications Applicable for drying big particles, heavy particles in chemical, mining, and metallurgy, such as mining area, cinder of blast furnace, coal, powder of metal, phosphate fertilizer and thiamine. For drying the powder or particles with special requirements, such as HP foaming blowing agent, residule of alcohol, light calcium carbonate, active clay, magnetic powder, graphite, and residue of medicine. For materials to be dried under low temperature and large lot continuous production . Feature The motorization level of the barrel is high, and the production capacity is high; The resistance that the material passes through the barrel is less, and the power consumption is low. Application capability to different characters of materials is high. The operation is stable, the operation fee is low, and the uniformity of product drying is good. modeldirect heating clockwise flow specdirect heating clockwise flow specheat directly countercurrent specheat directly countercurrent speccomplex heatcomplex heatkinds of raw materialorevesiccantblast fumaceammonium sulfatephosphorus fertilizercoalamount to be treated kg/h10004661500020000120005000primary moisture %301361.556.5final moisture %150.310.10.10.1average diameter mm6.50.054.70.5-1.70.55bulk density of rawmaterial kg/m 2770800189011001500750amount of hot air kg/h390005400107509800650016000temperature of air at inlet600165500180650570temperature of raw material at outlet 42100708075way of heatinggaselectric heatingheavy oilfuel hot fumaceheavy oilheavy oilloading effciency % 6.377.57.818revolution r.p.m443.5342gradient m/m0.040.0050.030.050.050.043quantity of stirring-up rake12241222outer of inner cylinder 8 inner of out cylinder 166 12diameter of dryer m2.01.522.3out cylinder 2 inner cylinder 0.84out cylinder 2.4 inner cylinder 0.95length of dryer m201217151016driving power kw227.515111115

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji YPG Pressure Spray Drying (Cooling) Granulator (YPG Series)

Because of different products have different drying technologies and particle rules, there is no single type of the spray drying machines that meet all kinds of different requirements. Now spraying is still regards as a kind of technology. The test is the base of correctly choosing the types. The machine equipped by our Company is used specially for the carry out the technological test of the materials. This kind of practical manner makes that we have completed many turn-key projects, such as: Detergent powder, polymerized resin, white carbon, Mn3O4, soybean milk, lipase, sea cucumber Chinese traditional medicine and etc. Description The material is sprayed into fine mist by nozzle on the top of tower. Follow the heat wind, the material is dried. The machine's characteristic is high collection rate, no stick onto the wall, energy saving, high efficiency, especially applicable for heat sensitive material. It's widely used in food, dyestuff, chemical industry and so on. Application: Food Industry: Fatty milk powder, protein, cocoa milk powder, subsitute milk powder, egg white (yolk), food and plant, oats, chicken juice, coffee, instant dissoluble tea, seasoning meat, protein, soybean, peanut protein, hydrolysate and so forth. Sugar, corn syrup, corn starch, glucose. Pectin, malt sugar, sorbic acid potassium and etc. Medicine: Traditional Chinese medicine extract, ointment, yeast, vitamin, antibiotic, amylase, lipase and etc. Plastics and resin: AB, ABS emulsion, uric acid resin, phenolic aldehyde resin, urea-formaldehyde resin, formaldehyde resin, polythene, poly-chloroprene and etc. Detergent: Common washing powder, advanced washing powder, soap powder, soda ash, emulsifier, brightening agent, orthophosphoric acid and etc. Chemical industry: Sodium fluoride (potassium ), alkaline dyestuff and pigment, dyestuff intermediate, Mn3O4, compound fertilizer, formic silicic acid, catalyst, sulphuric acid agent, amino acid, white carbon and so on. Ceramic: Aluminium oxide, ceramic tile material, magnesium oxide, talcum and so on. Other: Calmogastrin, hime chloride, stearic acid agent and the cooling spray. spec501001502003005001000Water evaporation capacity Kg/h501001502003005001000Overall dimension (diameter*H) mm1600×89002000×115002400×135002800×148003200×154003800×188004600×22500High-pressure pump pressure Mpa2-10Power Kw8.5142224308230Inlet air temperature300-350product water contents %less than 5 percent, and 5 percent can be achieved.collection rate %>97electric heater Kw75120 150When the temperature is lower then 200, the parameters should be calculated according to the practical condition.electricity + steam Mpa+Kw0.5+540.6+900.6+108hot air furnace Kcal/h1000001500002000003000004000005000001200000

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji PZG Continuous Plate Dryer (PGZ Series)

PGZ Series Continuous Plate Dryer Description PLG series continuous plate dryer is a kind of high efficiency conducting and continuous drying equipment. Its unique structure and operating principle provide advantages of high heat efficiency, low energy consumption, less occupying area, simple configuration, easy operation and control as well as good operating environment etc. It is widely used in drying process in the fields of chemical, pharmaceuticals, agricultural chemicals, foodstuff, fodder, process of agricultural and by-products etc., and is well received by various industries. Features: (1) easy control, wide application 1. Regulate thickness of materials, rotating speed of main shaft, number of harrow's arm, style of and sizes harrows achieve best drying process. 2. Each layer of drying plate can be fed with hot or cold media individually to heat or cold materials and make temperature control accurate and easy. 3. Dwell time of materials can be accurately adjusted. 4. Single flowing direction of materials without return flowing and mixing, uniform drying and stable quality, no re-mixing is required. (2) Easy and simple operation 1. Start stop of dryer is quite simple 2. After material feeding is stopped, they can be easily discharged out of the dryer by harrows. 3. Careful cleaning and observation can be carried inside the equipment through large-scale viewing window. (3) Low energy consumption 1. Thin layer of materials, low speed of main shaft, small power and energy required for conveying system of materials. 2. Dry by conducting heat so it has high heating efficiency and low energy consumption. (4)Good operation environment, solvent can be recovered and powder discharge meet the requirements of exhaust. 1. Normal pressure type: As low speed of air flow inside the equipment and moisture being high in upper part and low in lower part, dust powder couldn't float to the equipment, so there is almost no dust powder in tail gas discharged from the moist discharge port on the top. 2. Closed type: Equipped with solvent recovery device that can recover organic solvent easily from moist-carrier gas. The solvent recovery device has simple structure and high recovery rate, and nitrogen can be used as moist-carrier gas in closed circulation for those subject to burning, explosion and oxidation, and poisonous materials in order for safe operation. Especially suitable for drying of flammable, explosive and poisonous materials. 3. Vacuum type: If the plate dryer is operating under vacuum state, it is particularly suitable for drying heat sensitive materials. Application: Drying, heat decomposition, Combustion, cooling, reaction, And sublimation 1. Organic chemicals 2. Mineral chemicals 3. Pharmaceutical and foodstuff 4. Feed and fertilizer specdiameter mm high mm area of dry m 2power Kwspecdiameter mmhigh mmarea of dry m 2power Kw1200/4185026083.31.12200/182900578255.45.51200/630284.92200/20620261.61200/834486.61.52200/22662267.77.51200/1038688.22200/24704273.91200/1242889.92200/26746280.01500/6210030228.02.23000/83800405048111500/8344210.73000/104650601500/10386213.43000/125250721500/12428216.13.03000/145850841500/14470218.83000/166450961500/16512221.53000/187050108132200/62900326218.53.03000/2076501202200/8368224.63000/2282501322200/10410230.83000/2488501442200/12452236.94.03000/269450156152200/14494243.13000/28100501682200/16536249.35.53000/3010650180

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji DWP DWP Series Mesh-Belt Dryer

Principle For DWP type air jet mesh-belt dryer, the hot air flows. Through narrow seams or holes, downward or upward to the materials on the transmission belt. Because the spray air speed is up to more than 15m/s, the heat transmitting film is very thin, the heat transmitting co-efficiency is big and the drying speed is fast. When the machine is used for the air tight grains, the above air jet flow will return to the top and the bottom flow will return to the bottom, take part in circulation. For some materials, the air flows will pass through the inside of the materials, the heat source can be steam, electricity, thermal furnaces and combustion oil flue and etc. Application DWP type spray air mesh-belt drying machine is mainly used for drying the fiber plate, plaster plate, carton board, pulp film, coated cloth and etc...The machine is also suitable for drying the sheet state material and some special materials. specunitDW-1.2-8DW-1.2-10DW-1.6-8DW-1.6-10DW-2-8DW-2-10belt widthm1.21.21.61.622drying section lengthm810810810thickness of the materialmm10-80operation temperaturedegree60-130steam PressureMpa0.2-0.8steam consumption capacityKgsteam/kgH 2 O2.2-2.5drying strengthKgH 2 O/h6-20total power of fanKw5.57.57.5111115total power of machineKW6.258.258.2511.7511.7515.75

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji LZG Screw Helix Vibrating Dryer (LZG)

Features Because the hot air passes through the layer of raw material several tiers and acts counter motion towards the raw material, the heat exchanger is fully preferment and thermal efficiency is high. The structure is compact and it occupies small area. The stay time of raw material in thehelix bed can be adjusted and the operation is very convenient The raw material acts the motion if circle at helix bed from up to low, at the same the equipment can jump itself, so the contact surface between hot air and raw material is increased too and the dry effects is strengthened. The equipment is suitable for continuous operation because of continuous feeding and discharging raw material. Meanwhile it is easy to meet the requirements of "GMP" It does not damage the surface and shape of raw material basically. It can not only maintain the roundness of pill but also decrease the rate of pills. Principle The wet raw material enters into helix bed from fed inlet at the top and moves along with the helix bed from up to low and make jumping to the bottom, under the effect of vibrating force and gravity and then it's discharger. Meanwhile clean hot air enters into it from the bottom of helix bed and carries out heat exchange with raw material on the helix bed fully and exhausts from the outlet at the top. In this way the dry purpose of wet raw material is realized. specLZG-1.0LZG-1.2LZG-1.4LZG-1.6LZG-1.8diameter(mm)10001200140016001800power(kw)2×0.752×0.752×1.52×1.52×2.2Overall dimension (m)1.2×1.2×2.71.4×1.4×2.71.6×1.6×3.31.8×1.8×3.32.0×2.0×3.3weight(kg)14001680280031003800production capacity(kg/h)80-120120-200200-280280-350350-450temperature of air inlet( degree)60-20060-20060-20060-20060-200air amount(m 3 /h)14872380372144625930Poweer of fam(kw)5.57.51518.522

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji PZG ZPD Series Vacuum Harrow Dryer

Features Being adapted the big area heating way, its heat conducting area is large and its heat efficiency is high. Being installed stirring in the machine, it makes raw material in cylinder form the state of continuous circle inside the cylinder, so the uniformity to be heated of raw material is raised greatly. Being installed stirring in the machine, pulpinese, paste-like mixture or powder raw materials can be dried easy. Principle It is an innovation horizontal batch-type vacuum dryer. The moister of wet material will be evaporated by heat transmission. The stirrer with squeegee will remove material on hot surface and move in the container to form cycle flow. The evaporated moisture will be pumped by vacuum pump. Application The following raw materials from pharmaceutical industry, foodstuff industry, chemical industry and so on can be dried. Suitable for pulpiness, paste-like mixture or powder raw material. Thermal sensitive raw material having the requirement to dry at lower temperature. Raw materials that are easy to oxidize or explode and have strong irritative or toxic. Raw materials that need to recover solvent. Note: The evaporated amount of water its related to the characteristics of raw materials and the drying temperature. With renew products unceasingly, the related parameter will be exchanged, it does not announce in advance, pardon! ItemModelNameUnitZPD-500ZPD-750ZPD-1000ZPD-1500ZPD-2000ZPD-3000ZPD-5000Working volumeL300450600900120018003000Over in the cylinderMm(diameter) 600 × 1500(diameter) 800 × 1500(diameter)800 × 2000(diameter)1000 × 2000(dia)1000 × 2600(dia)1200 × 2600(dia)1400 × 3400Stirring revolutionRpm5-255-125PowerKw45.55.57.5111522Design pressure of jacketMpa≤ 0.3Pressure in the cylinderMPa-0.09— -0.096

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

wanji CT,CT-C Hot Air Circulating Drying Oven (CT, CT-C)

CT, CT-C Series Hot-nlast-air Circulating Drying Oven CT-C series hot air circulating drying oven uses axial flow blower with a low noise and high temperature proof and an automatic temperature control system. The whole circulation system is the fully enclosed to make that the heat efficiency of the drying oven increases from 40% of the traditional drying oven to70% of the present one. The highest heat efficiency can reach 78%. The successful design of CT-T hot air circulation drying oven makes that the hot air circulation drying oven in our country can catch the advanced level both at home and abroad, Saving a large quantity of the energy in our country, enhancing the economic results of the enterprises, in 1990, the medicine management bureau of the State issued the industry standard and the uniform type(YY-0026-90). ~ This drying oven is suitable for the material and for the product hot solidification and drying de-watering in the pharmaceutical, chemical, food, farming, side-product, aquatic product, light industries, heavy industry and other industries. Such as: Raw material medicine, crude drug, herbal medicine of Chinese traditional medicine, plaster, powder, particle, drinking agent, pill, packing bottle, pigment, dyestuff, de-watering vegetable, dried fruit piece, sausage, plastics and resin, electric component, baking varnish and etc. Most hot air is circulated in the oven. Which make the heat efficiency high and the energy economic. By using the forced ventilation function, there are the adjustable air distribution plates inside the oven. The materials can be dried uniformly. The heating source can use steam, hot water, electricity and far infrared, with a wide selection. The whole machine is low noise. The operation is in balance. The temperature is controlled automatically. The installation and maintenance are easy and the application is wide. Which can be used for drying various materials and is a versatile drying equipment. Type for the industry standardType and specificationDrying capacity for each time (Kg)power (KW)Steam to be consumed (Kg/h) (Kg/h)Heat radiation area(m 2 )Air capacity(m 3 /h) (m 3 /h)Temperature between the top and the bottom ()Baking plateOverall dimension (LxWxH) mmBaking cart to be used (set)RXH-4-B CT-I1001.120203400±2482430×1200×23752RXH-27-BCT-II2001.140405200±2962430×2200×24334RXH-41-BCT-III3002.260809800±21443430×2200×26206RXH-54-BCT-IV4002.2801009800±21924380×2200×26208RXH-5-CCT-C-0250.45553400±2161550×1000×20440RXH-14-CCT-C-IA500.4510103450±2241400×1200×20001RXH-14-CCT-C-I1000.4518203450±2482300×1200×20002RXH-27-CCT-C-II2000.936406900±2962300×2200×20004RXH-41-CCT-C-III3001.35548010350±21442300×2200×20006RXH-54-CCT-C-IV4001.87210013800±21924460×2200×22908RXH-18-CCT-C-IB1200.920256900±1481460×2160×22502RXH-41-CCT-C-ISSpecial baking bottle2.2601006900±2 1140×6160×32406RXH-25-AHigh efficiency and high temperature far infrared bacterium reducing baking oven1200×1000×16004

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji RC RC Series Molten Granulator

Description: The product is a new style(molten property)molding granulator .when operation ,the liquid of work will be solid through transmission and cool,materials with 50 -300degree of melting point range can be molded and granulated.Its features no dust,improving productive enviorment ,having certain economic value (energy saving,economic of packaging container),exchanging product quickly ,beautiful appearance and uniform size of granulated granule,near semi-spherical granule,no thermal stress and so on ,the granule product is not only easy to pack ,transport and store but also convenient to measure ,mixing or re-melting ,it can produce continuously from feeding material to packing finished product.it can also reduce physical strength and adapts stepless speed variable.the flow can be adjusted.the operation is very convenient .it is widely used for petroleun industry ,fine chemical industry and so on.use the machine,different shape such as strip ,block and flake can be produced.adapt close form,loxic material can be processed too. Explanation: The material must be filtered .it is not permitted that the solid materials is entered into the granulated machine head.otherwise,it can lead to wear and tear or block machine head and affect the quality of graduation,the control of temperature that the change of temperature shoule not more than 3 degree , the cooling system should exist filtering screen.in general the temperature of cooling water should be 5-25degree.(the lower the water temperature ,the faster the molding ,the better the granule ,and the higher the output) JRF Series Coal Combustion Hot Air Furnace The furnace is the versatile hot air equipment, it is used with other equipment for drying various materials.the furnace is widely used for the heating and moisture removing for the grain ,seed,feed,fruit,de-watering vegetable ,nushroom ,edible fungus,tremella,tea, tobacco leaf,other farming products ,food,medicine ,chemical raw material ,light and heavy industry products. Principle: The furnace uses the high temperature resistant method so that its life is much longer than the life of the pipe arrangement hot air furnace ,the furnace uses the smoke and air longitudinal splashing heat radiation sheets and the negative pressure smoke elimination mode.there is no dust collected on the heat exchange position ,there is no need to carry out the cleaning ,the heat feature is stable,various coal and wood can be used as the fuel.the furnace is equipped with the air leading device and the combustion is complete .all the technical and economic indexes of the furnace have reached the advanced level at home. Features: The furnace combines the combustion with the heat exchange ,using the latest indirect heating technology that the heat exchange is taken place at the position of the high temperature in the furnace,the smoke and the air go into the different channels ,without any pollution for the heating ,the heat efficiency rate is high(up to 60-75%).the temperature increase is fast ,the furnace is smal in size,easy in the installation ,reliable in the operation and low in the price(making a comparison with one ton boiler,the price of this system is only half price of the heating system for the boiler) Model RC60-ARC60-BRC60-CRC60-DRC120-ARC120-BRC120-CRC120-D Area of heat transform (square meter) 2.63.64.65.37.39.310.816.6Power of motors ( KW )1.5/0.751.5/0.751.5/1.11.5/1.13/1.53/1.53/1.54/2.2Size ( mm )5600×1200×18007200×1200×18008800×1200×180010050×1200×18007200×1700×18008800×1700×180010050×1700×180014800×1700×1800Capacity ( kg/h )80-100100-150120-180150-250300-380360-420380-500500-800weight ( kg )13601580188020602380259028304210

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

Wanji PGL-B Spray Drying Granulator (PGL-B)

Applications Pharmaceutical industry: tablet, capsule granule, granule of Chinese medicine with on or low sugar Foodstuff; cocoa, coffee, milk powder, juice of granule, flavoring and so on. Other industries: pesticides, feed, chemical fertilizer, pigment, dyestuff and so on. Features: Integrate spraying, drying fluid granulating in one body to realize granulating from liquid in one step. Using the process of spraying, it is particularly suitable for micro auxiliary raw materials and heat sensitive raw materials. Its efficiency is 1-2 times that FL boiling granulating machine. The final moisture of some products can reach 0.1%. It is equipped with powder returning device. The rate of granule forming is more than 85% with 0.2-2mm of diameter. The improved inner roller multi-flow atomizer can treat the liquid extract with 1.3g/cm3 of gravity. PGL-B Spray Drying Granulator Pharmaceutical industry: tablet, capsule granule, granule of Chinese medicine with on or low sugar Foodstuff; cocoa, coffee, milk powder, juice of granule, flavoring and so on. Other industries: pesticides, feed, chemical fertilizer, pigment, dyestuff and so on. Integrate spraying, drying fluid granulating in one body to realize granulating from liquid in one step. Using the process of spraying, it is particularly suitable for micro auxiliary raw materials and heat sensitive raw materials. Its efficiency is 1-2 times that FL boiling granulating machine. The final moisture of some products can reach 0.1%. It is equipped with powder returning device. The rate of granule forming is more than 85% with 0.2-2mm of diameter. The improved inner roller multi-flow atomizer can treat the liquid extract with 1.3g/cm3 of gravity. PGL-B Spray Drying Granulator Pharmaceutical industry: tablet, capsule granule, granule of Chinese medicine with on or low sugar Foodstuff; cocoa, coffee, milk powder, juice of granule, flavoring and so on. Other industries: pesticides, feed, chemical fertilizer, pigment, dyestuff and so on. Integrate spraying, drying fluid granulating in one body to realize granulating from liquid in one step. Using the process of spraying, it is particularly suitable for micro auxiliary raw materials and heat sensitive raw materials. Its efficiency is 1-2 times that FL boiling granulating machine. The final moisture of some products can reach 0.1%. It is equipped with powder returning device. The rate of granule forming is more than 85% with 0.2-2mm of diameter. The improved inner roller multi-flow atomizer can treat the liquid extract with 1.3g/cm3 of gravity. Example of model choice: Suppose that are 120kg liquid extract I (include 30% solid) and 60kg seed II in one vessel, from I and II, we can get theoretical product amount M=mI+mII=120kgx30%+60kg=96kg, working time T=120kg/30kg/h=4h, from the parameter table we can find that the fluidization amount is inside the standard loading range. If we require two batches in one duty time, model PGL-30B is OK. Itemunit specPGL-3BPGL-5BPGL-10BPGL-20BPGL-30BPGL-80BPGL-120Bliquid extractminkg/h24510204055maxkg/h4615304080120fluidization capacityminkg/batch26103060100150maxkg/batch6153080160250450specific gravity of the liquidkg/L≤1.30volume of material vesselL26502204206209801600diameter if vesselmm4005507701000120014001600power of suction fankw4.05.57.515223045power of auxiliary fankw0.350.750.751.202.202.204steamconsumptionkg/h407099210300366465pressureMpa0.1-0.4power of electric heaterkw9152125.551.56075compressed airconsumptionm 3 /min0.90.90.90.91.11.31.8pressureMpa0.1-0.4operating temperature automatically regulated from indoor temperature to 130water content of product%≤0.5% (depends on the material)rate of product collection%≥99%noise level of machinedB≤75weightkg50080012001500200025003000dim. of main machineΦmm4005507701000120014001600H 1mm940105010701180162016201690H 2mm2100240026803150363041204740H 3mm2450275030203700410047705150Bmm74089011101420160018202100

Changzhou Wanji Drying & Granulating Equipment Co., Ltd.

RXH-I Air cycle oven

RXH. series hot air circulation oven adopts noise elimination and thermal stable axial flow fan and automatic temperature control system. The entire circulation system is enclosed to make that the heat efficiency of the drying oven increases from 3~7% of the traditional drying oven to 35~45% of the present one. The highest heat efficiency can be up to 50%. The successful design of CT-C hot air circulation oven makes that the hot air circulation drying oven in our country reach the advanced level in the world. It saves energy and increases the economic benefit. Principles: This drying oven is suitable for the material and product hot solidification and dry de-watering in the pharmaceutical, chemical, food, farming, side-product, aquatic product, light industries, heavy industries and others industries. Such as: raw material medicine, crude drug, prepared herbal medicine of Chinese traditional medicine, plaster, powder, particle, drinking agent, pill, packing bottle, pigment, dyestuff, de-watering vegetable, dried fruit piece, sausage, plastics, resin, electric component, baking varnish and etc. Features: Most hot air is circulated in the oven. The Heat efficiency is high and the energy is saved. By using the forced ventilation function, there are adjustable air distribution plates inside the oven. The materials can be dried uniformly. The heating source might be steam, hot water, electricity and far infrared. With a wide selection. The whole machine is low in the noise. The operation is in balance. The temperature is controlled automatically. The installation and maintenance are easy. The application is wide. The machine can be used for drying various materials and is a versatile drying equipment.

AOTLE 6 temperture adjust drying room for artificial marble

It is a necessary facility ,adjust temperature .so that control the curdle time , and avoid aberration

XH(XINHUI) UV machine

Model：XH-102-150T ■ Application UV adhesive, UV clean oil,UV glue curing. ■ Application Industry PC,ABS; fiber,glasses, plastic,UV curing, LED light ; cables, mini-motor, electron… ■ Technical Parameter UV Lamp ：2.0KW*1pc； UV radiation length： 200mm； UV main wave length：365nm； Distance between Lamp and delivery belt can adjust: 50-150mm In Put / out put height ：10~100mm can be adjust； In put length：185mm； Out put length：185 mm； After 3 Minutes, UV radiation light will get its 100% out put. Lamp life time :800H； Speed adjust：1-10m/min. Delivery belt width：150mm； Belt width：150mm； Belt meterial：Black Teflon or stainless steel ； Machine Size ：1250×280×430mm（L×W×H）； Power supply： 220VAC 50HZ( Is there any different in your country? Please tell us if different)